DV Industrial Computer Ltd.
 | News  | Products  | Support  | Ordering  |   
D17 19" 1U chassis 510mm DEEP
Chassis D17
Form Factor
1U chassis support for (305x244mm) ATX motherboard
Height: 43mm
Width: 483mm
Depth: 510mm
Net weight: 7 kg
Expansion slots
- 1x Full-height PCI expansion slot (horizontal)
Drive Bays
- 4x HDD
Front Panel
- Hard drive activity
- Power
- Alarm
- Reset
- Power

Detailed description
System Cooling
- 2x D4028V12HB-J 10600RPM fans, 0.88m3/min total
Operating Environment (System)
Operating Temperature Range: +5~50º
Power Supply
PSU 350W
Input Voltage 100~240VAC
+3.3V 20A
+5V 25A
+5V standby 2A
-5V 0.3A
+12V 20A
-12V 0.8A
Mounting in rack
- Slide Rail Kit, look at application notes
Height: 100mm
Width: 520mm
Depth: 580mm
Gross weight: 8 kg
Available Colors
 RAL7032 Beige     RAL9005 Black

Ordering Information Part number Description
Front panel color D17350-W
Power Supply D17350 350W
Backplate shield D17350-== D17 chassis with "==" plate

Wide cutout on a back side for rear I/O connectors. This cutout is covered by special low profile shield/backplate. Multiple types of plates for the most popular Mini-ITX and micro-ATX motherboards are available (optional).

Optional Parts List Model Description
PCI riser card 1U1FR 1U riser changes the insert direction of the slot by 90 degrees. more>>
PCIe riser card 1U1FR-e1 1U PCI Express x1 riser card changes the insert direction of the slot by 90 degrees. more>>
1U1FR-e4 1U PCI Express x4 riser card changes the insert direction of the slot by 90 degrees. more>>
FanMagic controller - Internal airflow temperature monitoring and WatchDog timer. more>>
Fan D4028V12HB-J Additional cooler with 0.44m3/min more>>>

Chassis with 2 additional fans (optional) Technical drawing
D17 with 2 additional fans D17, technical drawing

Riser Card 1U1FR (1U1FR-e1, 1U1FR-e4) and I/O card installation
click to vew large picture

Riser card 1U1FR (1U1FR-e1, 1U1FR-e4) is used to change the insert direction of I/O card to the slot of motherboard by 90 degrees. The I/O card is plugged into the riser card and resides parallel with the motherboard. The D17 case and 1U1FR (1U1FR-e1, 1U1FR-e4) riser card provide expansion for one I/O card. Picture at the left shows the PCI slots location on a 7-slots standard ATX form factor board (starting from the left): PCI slot-1, slot-2, slot-3, slot-4, slot-5, slot-6 and PCIe (or AGP) slot-7 (On a Micro ATX board, there are only PCI slot-4, slot-5, slot-6 and PCIe (or AGP) slot-7 ). The position of slot-6 corresponds with the horizontal cutouts of the D17 chassis. Keep in mind that your motherboard should have PCI (PCIe) slot-6 in order to provide riser card plugging. Also, keep in mind a safe space between components on top surface of I/O card and the cover of chassis. Use a non-conductive self-adhesive bumpone to prevent the I/O card from short-circuiting with the cover of the chassis.
Riser card is supplied as option, but it is advisable to order required riser card together with chassis.

Slide Rail Kit installation
click to vew large picture

click to vew large picture

click to vew large picture

The Slide Rail Kit is supplied together with the D17 chassis. Remove the D17 chassis from the packaging box and check that the Kit is included. The Kit consists of two symmetric Holders - left and right. Each Holder consists of two parts - Front Bracket (1) and Back Bracket (2). Slide together the front to back sections of the Holders as shown on the picture on the left. Extend the Holders to the length required to fit the rack or cabinet before you install it. The Kit supports rack fixing distance on depth L from 340mm to 639mm. Notify, there are two variants to join Back Bracket (A and B). Screw on appropriate nuts (3) (supplied with the Kit) to each bracket, and tighten the front and the back sections.

Install 8 cage nuts in the rack (not supplied with the Kit). Reffer to the picture on the left. You should install 4 cage nuts (red marked) and tighten the both Holders with 3 appropriate screws for EACH SIDE of the rack (left and right). You need to tighten 6 screws total.
Note! Please make sure the salient side of each Holder (left and right) is in the opposite position in the rackmount.

Slide the D17 based system with fastened cover along the pre-installed Holders in the suitable rack. Tighten the other 2 screws on the opposite side of the front panel where it attaches to the rack.

Home  | Contact Us  | About Us |