DV Industrial Computer Ltd.
 | News  | Products  | Support  | Ordering  |   
DL17 19" 1U chassis 640mm DEEP
Chassis DL17
Form Factor
1U chassis support for extended (305x330mm) ATX dual Xeon motherboard
Dimensions(mm)
Height: 43mm
Width: 483mm
Depth: 640mm
Net weight: 9kg
Expansion slots
- 1x Full-height PCI expansion slot (horizontal)
Drive Bays
- 4x HDD
Front Panel
LEDs:
- Hard drive activity
- Power
- Alarm
Buttons:
- Reset
- Power

Detailed description
System Cooling
- 2x DB9733V12HB 3600RPM blowers, 1.48m3 total
Operating Environment (System)
Operating Temperature Range: +5~50º
Power Supply
PSU 460W
Input Voltage 100~240VAC 
+3.3V 30A
+5V 30A
+5V standby 2A
-5V 0.3A
+12V 32A
-12V 0.8A
Mounting in rack
- Slide Rail Kit, look at application notes
Package
Height: 70mm
Width: 500mm
Depth: 700mm
Gross weight: 10kg
Available Colors
 RAL7032 Beige     RAL9005 Black

Ordering Information Part number Description
Front panel color DL17460-W
DL17460-B
White(Beige)
Black
Power Supply DL17460 460W
Backplate shield DL17460-== DL17 chassis with "==" plate

Wide cutout on a back side for rear I/O connectors. This cutout is covered by special low profile shield/backplate. Multiple types of plates for the most popular Mini-ITX and micro-ATX motherboards are available (optional).

Optional Parts List Model Description
PCI riser card 1U1FR 1U riser changes the insert direction of the slot by 90 degrees. more>>
PCIe riser card 1U1FR-e1 1U PCI Express x1 riser card changes the insert direction of the slot by 90 degrees. more>>
1U1FR-e4 1U PCI Express x4 riser card changes the insert direction of the slot by 90 degrees. more>>
FanMagic controller - Internal airflow temperature monitoring and WatchDog timer. more>>

Computer in chassis Chassis without cover Technical drawing
Computer in chassis DL17 DL17 without cover DL17, technical drawing

Riser Card 1U1FR (1U1FR-e1, 1U1FR-e4) and I/O card installation
click to vew large picture

Riser card 1U1FR (1U1FR-e1, 1U1FR-e4) is used to change the insert direction of I/O card to the slot of motherboard by 90 degrees. The I/O card is plugged into the riser card and resides parallel with the motherboard. The DL17 case and 1U1FR (1U1FR-e1, 1U1FR-e4) riser card provide expansion for one I/O card. Picture at the left shows the PCI slots location on a 7-slots standard ATX form factor board (starting from the left): PCI slot-1, slot-2, slot-3, slot-4, slot-5, slot-6 and PCIe (or AGP) slot-7 (On a Micro ATX board, there are only PCI slot-4, slot-5, slot-6 and PCIe (or AGP) slot-7 ). The position of slot-6 corresponds with the horizontal cutouts of the DL17 chassis. Keep in mind that your motherboard should have PCI (PCIe) slot-6 in order to provide riser card plugging. Also, keep in mind a safe space between components on top surface of I/O card and the cover of chassis. Use a non-conductive self-adhesive bumpone to prevent the I/O card from short-circuiting with the cover of the chassis.
Riser card is supplied as option, but it is advisable to order required riser card together with chassis.

Slide Rail Kit installation
click to vew large picture

click to vew large picture

click to vew large picture

The Slide Rail Kit is supplied together with the DL17 chassis. Remove the DL17 chassis from the packaging box and check that the Kit is included. The Kit consists of two symmetric Holders - left and right. Each Holder consists of two parts - Front Bracket (1) and Back Bracket (2). Slide together the front to back sections of the Holders as shown on the picture on the left. Extend the Holders to the length required to fit the rack or cabinet before you install it. The Kit supports rack fixing distance on depth L from 428mm to 726mm. Notify, there are two variants to join Back Bracket (A and B). Screw on appropriate nuts (3) (supplied with the Kit) to each bracket, and tighten the front and the back sections.

Install 8 cage nuts in the rack (not supplied with the Kit). Reffer to the picture on the left. You should install 4 cage nuts (red marked) and tighten the both Holders with 3 appropriate screws for EACH SIDE of the rack (left and right). You need to tighten 6 screws total.
Note! Please make sure the salient side of each Holder (left and right) is in the opposite position in the rackmount.

Slide the DL17 based system with fastening cover along the pre-installed Holders in the suitable rack. Tighten the other 2 screws on the opposite side of the front panel where it attaches to the rack.


Home  | Contact Us  | About Us |