DV Industrial Computer Ltd.
 | News  | Products  | Support  | Ordering  |   
PSU DP024 Smart Automotive PSU 24V Input
The DP024 is a fully compliant ATX power supply designed to power a low power system from a single 24V power source of a vehicle. As the DP024 does not contain neither electrolytic nor tantalum no polymer (solid state) capacitors it can be used for long time at 50°C and higher without fundamental loss of reliability. The DP024 power supply has an MCU that controls and monitors various functions of the power supply operation. Also, it realizes voltages monitoring, temperature monitoring and communication via COM-port with computer. A LED indicator continually reports the power system status and health. Also, you can use it for troubleshooting. As well the MCU realizes a WatchDog timer to supervise the computer. There are four main operating modes of the DP024 - Deep Sleep, Sleep, Standby, Power On. The DP024 has user selectable MCU driven timing settings, allowing you to choose various ignition/shutdown vehicle computer timing schemes (settings). These settings are user adjusted and saved in EEPROM.

One of most difficult tasks of operating a computer in a vehicle is power consumption while the computer is OFF. Even if your computer is totally OFF (standby mode), a computer will still consume a few hundred milliwatts, needed to monitor computer ON/OFF status. All power supplies provide 5Vsb (5V standby) so that the motherboard can issue at least a PSON signal. When the computer is in the suspend/sleep mode, it will consume even more power, because the RAM needs to be powered at all times. The power consumption in the suspend mode is few Watts. No matter how big your car battery is, it will eventually drain your vehicle battery in a matter of days. The DP024 is addressing these issues by cutting off the 5VSB rail after a pre-defined amount of time (timing settings). The DP024 monitors battery voltage to protect against deep discharge. When battery level drops below predefined value for more than predefined time, the DP024 will shut down and re-activate only when the input voltage is > predefined value.

Of course, there is a traditional PC PSU mode setting with no ignition control (shutdown logic bypassed) and it can be used in non-vehicle computer applications.
- Wide input range (19-35V)
- Suitable for automotive applications
- Suitable for battery powered applications
- Complete with start-up/shut-down control (saved in EEPROM)
- Compatible with most ITX boards equipped with a 20pin ATX connector
- Long life even at temperature higher than 50ºC
- Silent operation (fanless)
- Temperature control
- Low heat dissipation (efficiency over 85%)
- Open frame, chassis mountable, measurements: 36x170x26
- Connection via COM-port with computer
- WatchDog timer to supervise the computer (by commands through the COM-port)
- Output power 90W.
- Input voltage : +19~35VDC (nominal - 26V).
- Output : +12V 0~4A | +5V 0~6A | +3,3V 0~6A | -12V 0~0,1A | +5Vsb 0~6A
  (at 26V input)

NOTICE: Total current on 5Vsb and 5V rails does not exceed 6A. Do not connect a Car Battery Charger directly to the DP024.

Connection to car electrical system

The DP024 should be attached and tuned by specialized personnel only after familiarizing with User manual Please take a moment and read this manual before you install the DP024 in your vehicle. Often rushing into installing the unit can result in serious damage to your DP024 converter, computer and probably your car electrical system. The DP024 has several wires that need to be installed in various places. When installing, always double check the polarity of your wires with a voltmeter. NEVER use the cigarette plug as a power source; often the contacts are not capable of delivering high current to your PC. Also, refer to the following sheet for the DP024 connection.

Connect the IGNITION+ to the switched +24 Volt supply wire (“ignition” circuit or fuse box).

Connect GND and POWER circuits with heavy gauge wire directly to the automotive batteries (+) and (–) terminals. GND may also be connected with heavy gauge wire to the Chassis if desired.

Apply 24 Volts to IGNITION+ by turning on the ignition or by flipping a switch and you’re ready to go!

NOTICE! It is desirable to connect the DP024 to 24V car electrical system via surge protector (shown hatched). This device should suppress glitches above 40V that sometimes occur in 24V car electrical system and should provide conducted immunity according to ISO7637.

The DP024 can be tested in the lab before being installed into the vehicle. Certain details need to be noted for proper bench testing. When connecting bench power use between 24 to 32 Volts DC to POWER (+) and GND (BATTERY) (-) terminals for best results. The best way to do successful bench testing is to use an adequately sized 24V battery. Bringing in the battery from the car or using an extra one that has at least a 10-AmpHour capacity will be sufficient in most cases. To aid in bench testing, do not connect IGNITION+ anywhere. The DP024 will operate as “dumb PSU” with button “POWER” control.

Connection to the battery that is charged by AC-DC charger;
Creation of high efficiency uninterruptable power supply (UPS)

Connect GND and POWER circuits with heavy gauge wire directly to the batteries (+) and (–) terminals and charger as shown on figure below. Charger should have rectangular output characteristic (constant current with voltage limit) that has been complied with battery parameters. This compliance is quite difficult and is beyond the scope of this application note and will not be discussed here.

CAUTION! Wrong type of battery and charger maybe the cause of low efficiency this circuit and even maybe the cause of demage of battery and charger.

Home  | Contact Us  | About Us |